注塑机 挤出机 造粒机 吹膜机 吹塑机 吹瓶机 成型机 吸塑机 滚塑机 管材生产线 板材生产线 型材生产线 片材生产线 发泡设备 塑料压延机
四川川大干燥科技工程有限责任公司
暂无信息 |
一、工作原理及应用范围介绍IntroductionofWorkingPrincipleandScopeofApplication本机组以干燥洁净的压缩空气为动力源
一、工作原理及应用范围介绍 Introduction of Working Principle and Scope of Application
本机组以干燥洁净的压缩空气为动力源,通过气流高速喷射,使粉碎室内形成一个粉碎、分级圆面,并在粉碎室内形成压力差,则物料自动吸入粉碎室,在4到16个喷头所喷出的超音速气流作用下(产生冲击能E=1/2mv2),物料在分级圆面上作高速运动(通常在2-3马赫内)使物料作相互高速高能的摩擦、碰撞、撕裂等作用,从而达到超细粉碎之目的。
适用于莫氏硬度1-7级各类干燥脆性物料,物料粒度100-400目,含水量低于3%,本机可进行粉碎的物料非常之广,例如:各种矿石、化工、电子、农药、医药、中药等各类产品,并适合热敏性、低熔点物料。产品粒度一般可达到1-10μm,粒径≤20μm,有些物料甚至可达到0.5-0.1μm。
The dry and clear compressor air is adopted as power source of this equipment; under the high-speed jetting of air flow, one pulverizing and grading disc, as well as pressure difference are formed in the pulverizing chamber, thus to automatically absorb the materials in the pulverizing chamber; under the actions of supersonic speed air flow jetted from 4-16 sprayers (impact energy E=1/2mv2), the materials move at high speed on the grading disc (generally within 2-3mach) to generate friction, compact and tear with high speed and energy, thus to realize the superfine pulverizing purpose.
It is applicable to various dry and brittle materials with Mohs hardness of 1-7, particle size of 100-400 meshes and water content lower than 3%. This equipment can be used for many materials, such as various minerals, chemicals, electronics, pesticides, medicines and traditional Chinese medicines, and is applicable to materials with heat sensitivity and low melt point. In generally, the particle size of materials is 1-10μm with maximum of ≤20μm; for some materials, it can up to 0.5-0.1μm.
二、特点Characteristics
1.高速气流粉碎,物料在粉碎工程中不会有大的升温。
2.本系统因粉粹出来的产品细度非常细,属于高精超微加工设备,对于提升产品的性能、功能以及价值有作用。
3.粉碎过程无噪音,自动化程度高。
4.特别适合粉碎热敏性物料以及要求很细的脆性物料。
1. The high-speed air flow is adopted for pulverizing, no significant temperature rising caused during the pulverizing process.
2. This is high-accurate and superfine processing equipment due to the high fineness degree of pulverized products, and has unit effects in improving property, function and value of products.
3. There is no noise generated during the pulverizing, and it is high in the degree of automation.
4. Especially, it is applicable to pulverizing of heat-sensitivematerials and brittle materials with high finesses requirement.
三、工艺流程图Process flow diagram
四、技术参数(下表中数值仅供选型时参考)
Technical parameters (the values in the table below are for reference in type selection only)
超音速气流粉碎机
您感兴趣的产品PRODUCTS YOU ARE INTERESTED IN
塑料机械网 设计制作,未经允许翻录必究 .
请输入账号
请输入密码
请输验证码
请输入你感兴趣的产品
请简单描述您的需求
请选择省份