PCS-100断刀检测器 PCS-100断刀检测器
PCS-100
断刀检测器
破损检测器
破损检测系统
深圳市汉斯福特科技有限公司
李工
：
: 3174269615
公司地址：龙华新区大浪街道大浪社区伟达工业园A栋2楼
公司：www.huntsort。。ｃｏｍ
- Uni-body Design for Ultimate Sealing
一体成型机身工艺，高密封设计
- Shaft-Direct Drive (Without Gear Box)
轴直接驱动式，不带齿轮箱
- Set Bolt
固定螺栓
- Adjust Ring for Swing Angle
旋角调整环
- V Cup Seal
V型密封
- Needle Cap (To be mounted or removed by the set screw)
针帽，可通过固定螺丝进行装卸
- Needle Length Std: 140mm Long Needle: 200mm Max.
探针长度，标准：140mm，zui大：200mm
- Flat Wand (Option) 110mm (L) 3mm (W)
防护杆（选装），长110mm，宽3mm
- Carbide deposited
针表面超硬化处理
探针摆动 | 摆动角度5-175° |
电机驱动 | 直接驱动式直流电机 |
工作电压 | 直流24V |
zui大电流 | 250mA |
运行温度 | 0-55℃ |
1. Contact Sensor PCS-100 with Needle Assembly
接触式传感器/探头PCS-100以及探针配套装置
Contact sensor PCS-100
- Rotation angle can be set and/or changed flexibly CW or CCW, in the range of 5° to 175°.
可通过设置或者更改旋转方向来调整旋转角度，调整范围为5°到175°.
Setting CW or CCW on the control unit depends on where the sensor/needle is set, and which one could achieve the nearest contact to the tool.
在控制器上操作，并据传感器探针的位置和就近被测工具的原则来调整旋转方向
- Contact pressure of needle (speed of needle swing) can be changed in 3 steps by the switch of control unit. The lowest swing speed is ideal for the small dia. of tools. Up to about 0.4mm dia. of tools can be detected.
只需要三步即可在控制器上调整探针的接触压力（探针旋转速度），zui低旋转速度适合测小尺寸的被测工具，zui小测量工具尺寸为0.4mm。
- Swing speed of the needle can be selected in several steps. It can help to minimize the cycle time of machining.
探针旋转速度只需要遵循几个步骤操作即可进行选择，这样能有效地缩短机器加工周期
2. Control Unit SCU-100
SCU-100控制单元
OK output
If a tool is detected, OK relay outputs a momentary or latch signal. Green LED illuminates.
当被测件被检测到良好，继电输出一个瞬间信号，绿LED灯亮起。
FAULT output
When a broken tool condition is detected, FAULT relay outputs a momentary or latch signal Red LED illuminates.
当检测到破损件时，瞬间发出一个故障信号，红色LED灯亮起
System Fault
A system Fault signal outputs at Fault relay when
在以下情况会发出系统故障信号：
- The sensor malfunction.
传感器故障
- The sensor direction setting and the CW/CCW switch setting are opposite.
传感器方向设置和正反旋转方向转换设置错反
- There is a short or disconnection at the sensor cable
传感器电缆线短路后者断开
Both Red and Green LED illuminate
此时红绿灯同时亮起
3. Connecting Cable (STD: 5m) with L90 Connector
配有L90接头的电缆线，标准长5m
4. Clamping Collar
夹圈
代理：深圳市汉斯福特科技有限公司
公司：www.huntsort。。ｃｏｍ
公司地址：龙华新区大浪街道大浪社区伟华达工业园A栋2楼
：
Housing 外壳 | Anodized Aluminum 阳极电镀铝 |
Needle swing 探针摆动 | Swing Angle 5-175°mechanically adjustable 摆动角度5-175°，机械可调 |
Needle 探针 | Max Life needle in standard length 140mm, Long needle 200 mm (Heat-Treated) 标准长140mm，zui长200mm（热处理） |
Motor drive 电机驱动 | Direct Drive (No Gear Box) DC motor 直接驱动式直流电机，不带齿轮箱 |
Sealing 密封 | Sealed against liquid and solid contaminants. Rating IP-67 高密封，防止液体和固体污染侵蚀，防护等级达IP67 |
Cable 电缆 | 90°or straight, moulded 4 pin connector. Standard length 5M (Max. 50M) 垂直或者水平电缆线，带4针接头，标准长5m，zui大长为50m |
| SCU-100 Control Unit SCU-100 控制单元 |
Operating voltage 工作电压 | 24VDC 直流24V |
Max. current zui大电流 | 250mA |
Operating Temp. 运行温度 | 0-55℃ |
Housing Material 外壳材质 | Polycarbonate 聚碳酸脂 |
Max. wire size zui大线规 | 12AWG |
Mounting 安装方式 | 35mm DIN Rail 35mm导轨，符合德国工业标准 |
OK Fault relay 正常/故障信号继电输出 | Dry Contact (Contact Rating) 干接触（接点容量） |
Additional Functions 附件功能 | Changeable to reverse logic for space monitoring 空间监测时，逆向理论信号切换 |
