现货型号1KH1N04R中国台湾HONOR钰盟齿轮泵
中国台湾HONOR钰盟高压齿轮泵 1KH1K系列：高压齿轮泵
1KH1K01L 1KH1K0SL 1KH1K02L 1KH1K03L 1KH1K04L 1KH1K05L 1KH1K06L 1KH1K07L 1KH1K09L
1KH1K01R 1KH1K0SR 1KH1K02R 1KH1K03R 1KH1K04R 1KH1K05R 1KH1K06R 1KH1K07R 1KH1K09R
1KH1S01L 1KH1S0SL 1KH1S02L 1KH1S03L 1KH1S04L 1KH1S05L 1KH1S06L 1KH1S07L 1KH1S09L
高压齿轮泵1AG1P
中国台湾HONOR高压齿轮泵1AG1P0SR,1AG1P01R,1AG1P02R,1AG1P27R,1AG1P35R,1AG1P04R,1AG1P05R,1AG1P06R,1AG1P07R,
中国台湾HONOR高压齿轮泵1AG1P09R,1AG1P0SL,1AG1P01L,1AG1P02L,1AG1P27L,1AG1P35L,1AG1P04L,1AG1P05L,1AG1P06L,
1AG1P07L,1AG1P09L,
现货型号1KH1N04R中国台湾HONOR钰盟齿轮泵
P101齿轮泵 P204齿轮泵 1AG1P01R齿轮泵 PFG齿轮泵
P102齿轮泵 P206齿轮泵 1AG1P02R齿轮泵 PFG-114齿轮泵
P127齿轮泵 P208齿轮泵 1AG1P27R齿轮泵 PFG-120齿轮泵
P135齿轮泵 P2011齿轮泵 1AG1P35R齿轮泵 PFG-128齿轮泵
P104齿轮泵 P214齿轮泵 1AG1P04R齿轮泵 PFG-135齿轮泵
P105齿轮泵 P216齿轮泵 1AG1P05R齿轮泵 PFG-142齿轮泵
P106齿轮泵 P219齿轮泵 1AG1P06R齿轮泵 PFG-149齿轮泵
P107齿轮泵 P222齿轮泵 1AG1P07R齿轮泵 PFG-160齿轮泵
P109齿轮泵 P225齿轮泵 1AG1P09R齿轮泵 PFG-174齿轮泵
P101RP01GT齿轮泵 P233齿轮泵 1AG1P11R齿轮泵 PFG-187齿轮泵
齿轮泵两端盖磨损之后的维修
齿轮泵的端盖用铸铁制造，出现磨损现象后，轻微的可在平板上研磨修平，磨损比较严重时应在平面磨床上磨削修平。修磨后的端盖与泵体配合连接的平面接触应不低于85%.平面度允差、端面对孔中心线的垂直度允差、两端面的平行度允差和两轴孔中心线的平行度允差均为o.olmm。磨削后的表面粗糙度ra应不大于1. 5μm。
4.齿轮泵用滚针轴承的维修更换
泵中零件维修后，轴承滚针应更换。对滚针要求是：全部滚针直径的尺寸误差不应超过0.003mm，长度允差为0.1mm，与轴配合间隙应在o.olmm左右;滚针装配时要按数量要求充满轴承壳内，滚针间要相互平行布置。
