注塑机 挤出机 造粒机 吹膜机 吹塑机 吹瓶机 成型机 吸塑机 滚塑机 管材生产线 板材生产线 型材生产线 片材生产线 发泡设备 塑料压延机
泉州联进机械有限公司
泉州联进机械有限公司
泉州联进机械有限公司QUANZHOULIANJINMACHINECO.,LTD数控切条机使用说明CNCCuttingMachine用途：用于橡胶切条、切纸等
泉州联进机械有限公司
QUANZHOU LIANJIN MACHINE CO., LTD
数
控
切
条
机
使
用
说
明
CNC Cutting Machine
用途：用于橡胶切条、切纸等。
特点：1.装有防护装置在使用时安全快捷。
2.上下切割，切料精准度高，最细可切至1mm.
3.采用伺服电机加触摸屏控制，操作方便、高效率。
主要技术参数 Technical Parameters | |
型号 Model | 伺服高效上下直切 |
外型尺寸 Appearance Size: L*W*H(mm) | 1450*1030*1300 |
重量Weight(kg) | 350 |
工作宽度Working Width(mm) | 600 |
切刀功率Power (KW) | 1.5 |
进料输送功率Power (KW) | 1.2 |
出料输送功率Power (KW) | 0.12 |
使用说明
公共设备电力：电压380V,50Hz。
主电源线：2.5平方毫米 四芯线
1. 机械运转中手切勿接触刀模及滚轮。
2. 橡胶片应该保持平整进料，防止。
3. 操作时不要双层料同时切，以免烧坏电机，发现送料滚筒卷料时，要及时关机清理，同时如有杂料在刀口工作部位要及时清理干净，清理时务必断开电源来源。
4. 原料不能有铁，石头等杂物，如发现要清理干净，以免损伤刀片。
5. 发现电机有异声，要停机检查，链条皮带松动要及时调整，螺丝松动要及时紧固。
6. 机台工作时，手一定不要伸进里面，如有问题，一定要停机解决。
7. 汽泵指针一般在3PMA左右，太大或太小气压都会影响切胶效果。
8. 如时间长，发现料切不断
①调整刀口间隙。
②修整刀口，检查刀口是否有损坏，如有损坏要及时修整。
9. 易损件部位要保持油路畅通润滑。
10. 新机台用少量粉撒在卷筒上，以免卷料。
11. 胶片进料有跑偏需调整两边气缸压力。
Purpose: This machine is used for cutting the rubber, paper etc.
Advantage: 1.Equiped with safety cover to secure safety on working.
2. Up-down cut High accuracy. The minimum can be cut to1mm.
3. Servo motor and touch screen control, easy to operate, high efficiency.
主要技术参数 Technical Parameters | |
型号 Model | 伺服高效上下直切 |
外型尺寸 Appearance Size: L*W*H(mm) | 1450*1030*1300 |
重量Weight(kg) | 350 |
工作宽度Working Width(mm) | 600 |
切刀功率Power (KW) | 1.5 |
进料输送功率Power (KW) | 1.2 |
出料输送功率Power (KW) | 0.12 |
INSTRUCTIONS:
Public equipment：Power: 380V,50Hz.
Host power line: 2.5mm² four-core
1. Do not touch the cutter die and roller during the operation of the machine.
2. Rubber sheet should be kept flat to prevent material from sticking.
3. When operating, do not cut rubber in double-deck at one time, which will cause the MOTOR to be too hot and broken. If the Material-sending Roller can not run smoothly. Please shutdown at once; meanwhile, if there are odds and ends at knife edge, please clean up in time .Do stop the power before cleaning.
4. No iron or stone in the material; if any, take them, away at once, so as not to make the blade damaged.
5. Any unusual voice, stop and check. Adjust chains and screws if they are loose.
6. Do stop the machine when there is problem. Do not put hands in when the machine is still working.
7. The indicator of the air pump is at about 3PMA. Too large or too small air pressure may have an effect on slicing.
8. After being operated for long time and the machine fails to cut off material.
① Adjust the blade clearance.
② customer should adjust the knife and check whether the blade is damaged and need repairing.
9. Kept the wearing parts being smooth & lubricative.
10. New machine please add proper amount of powder to the Rooller to avoid material rolling and jammed.
11. If the film feed is out of alignment, adjust the cylinder pressure on both sides.
您感兴趣的产品PRODUCTS YOU ARE INTERESTED IN
进口Italvibras MVSI 15/400-S02振动电机公司
MVSI 15/400-S02 面议
塑料机械网 设计制作，未经允许翻录必究 .
请输入账号
请输入密码
请输验证码
